Model 1HROVNOVAX - 14

ROVER NOVAX 14-M TURBO Nickel Impeller Pump
Beverage transfer pump suitable for wine, edible oils, milk, juices etc
14 litres per minute
maximum operating temperature: 30C
14mm in/Out
o.5hp 1 phase
(volts 220-240..Amps 0.50 Htz 50/60)
made in Italy

..POA

This Italian Imported Rover pump is specially made for the transfer of liquids such as wine, water, milk and oil (which have a small percentage of solids).

Model 1HROVBE-25

ROVER BE-M 25-TURBO Brass Impeller Pump
45 litres per minute
maximum operating temperature: 30C
25mm in/Out
o.6hp 1 phase
(volts 220-240..Amps 0.50 Htz 50/60)
Made in Italy

..POA

This Italian Imported Rover pump is specially made for the transfer of liquids such as wine, water, milk and oil (which have a small percentage of solids).

Model 1HROVNOVAX-25

ROVER NOVAX 25-M TURBO Nickel Impeller Pump
Beverage transfer pump suitable for wine, edible oils, milk, juices etc
40 litres per minute
maximum operating temperature: 30C
25mm in/Out
o.6hp 1 phase
(volts 220-240..Amps 0.50 Htz 50/60)
Made in Italy

..POA

This Italian Imported Rover pump is specially made for the transfer of liquids such as wine, water, milk and oil (which have a small percentage of solids).

Model
BE 30 Brass Impeller Pump
80 litres per minute
maximum operating temperature: 30C
20mm mm In/Out
1 hp 1 phase
(volts 220-240..Amps 0.50 Htz 50/60)
Made in Italy

....POA

This Italian Imported Rover pump is specially made for the transfer of liquids such as wine, water, milk and oil (which have a small percentage of solids).

Rover seal kit to fit BE M 20 ..$18.00

March Pumps 809 PL-HS : Hot liquid pump: Rated to 130C..$285.00 (fitted with Au plug)

The March pump is ideally suited to the home brewer for transferring hot wort. This pump is constructed of food-grade material, handles wort at boiling temperature and takes back pressure.

The pump housing is made from polysulfone, a tough food grade plastic.

The magnetic drive acts as a clutch allowing the user to put backpressure onthe pump to slow down the flow. It is not a self priming pump so needs to be primed.

Features include: Magnetic Drive, Rated to 130C degrees Celcius,
Food Grade, Teflon coated impeller, 21 litres/min, 2.7 metre head capacity
Inlet and Outlet 1/2" NPT.

Optional extras for March Pump

fitted with Blichmann Engineering (U.S.A) stainless steel quick connectors. $15.50 each. (image left)

March pump with stainless steel bracket to secure the pump to a bench or timber base....Buy bracket extra.....$38.00

Blichmann Engineering Stainless steel quick connector fittings

1/2 " NPT ......$15.50 (fit to 1/2" / 12mm Internal diameter hose)
Everything that touches your wort is stainless . Nickel plated brass nut won't lock-up on stainless fittings. Installs without tools! Easy disassembly and no hidden crevices means it's a snap to sanitize!

fits March pump, Blichman Therminator.

Submersible pump: Fully waterproof with high performance.

Made from high quality non corrosive parts.

Used for pumping of water. (e.g distillation cooling water)

220-240V 50Hz 100W
3500 litres an hour
Maximum Height 4.0m

$107.00

Pre-Filter. Added security for Buon vino wine filter/pumps or any pump that takes a 12mm ID hose
recommended for Buon vino Super Jet filter and pump
& Rover Novax 14 Nickel impeller pump (see top of page)

This pre-filter will preserve and lengthen the life of the check valve, by ensuring that no large particles like oak chips, grape skins tartaric crystals, hop leaves etc. are allowed into the pump, prematurely damaging it.

Base housing: Polypropylene
Top housing: Clear Polysulfone.
Interior: 304 Stainless steel 40 mesh (fine) screen
FDA approved
Flow rate for 1/2" barb.....5gpm @ maximum 70PS

HOSE BARBS:

Male pipe thread on one side,
hose barb on the other. Screw directly into 3 piece ball valves

Available in brass $.......
stainless steel $.......

or food grade polypropelene

316 stainless steel racking canes with sediment reducing tip.

measurements: Rod only
71cm (27" from bottom to bend at top) ..$22.50
This is sometimes called a 31" because they measure around the bend.
fits 60 litre fermenters

56cm (22" from bottom to bend at top)..$17.50
Once again this is sometimes called a 26" because of measurements around the bend

Request hose of your choice . Recommended hose selections would be

Pure silicone hose (if you wish to transfer hot /boiling liquids or just want a superior quality transfer hose.

or PVC or vinyl food grade beverage hose (for room temperature transfers)

Miscellaneous syphon parts

• glass syphon rod to fit 25 or 30 litre fermenter................$ 4.50
• rubber sediment reducing U Bend...................................$ 3.90
• food grade beverage hose(tubeing)1.5metre..................$ 3.80
• In line bottle filler (automatic cut off valve).......................$ 4.50

All fermenters supplied by ibrew/Bett-A-Brew are bored to house a 45mm rubber bung in the lid. This bung serves two purposes.

• 1. It holds the airlock in position (preferable to small grommit)and
• 2. It holds the syphon in position to prevent it moving about
• 45 mm rubber bung bored with hole..................$ 4.50

for more information on bottling sediment reduced home brew see article No. 5

for more information on Racking Wine for Clearer Results see article No. 9

Buon VinoSuper Automatic Bottle Filler..$39.95

The Buon Vino Super Automatic Bottle Filler allows for quick and easy filling of wine bottles for the home winemaker. The bottle filler is easily primed and is self levelling and self deactivating to help prevent accidental overflow. The specially designed tapered tip cascades wine into the bottle. In order to fill additional bottles, you need simplhy remove the automatic filler from the first bottl and place it into the next, pushing down on the activation lever to continue the wine flow